QTR-L-1RC Reflektionssensor (2-Pack)

Note: The QTR-L-1RC reflectance sensor requires a digital I/O line to take readings. The similar QTR-L-1A reflectance sensor is available with an analog output. Functional Description: The Pololu QTR-L-1RC reflectance sensor carries a right-angle infrared LED and a right-angle phototransistor, both pointing toward the front edge of the board. The phototransistor uses a capacitor discharge circuit that allows a digital I/O line on a microcontroller to take an analog reading of reflected IR by measuring the discharge time of the capacitor. Shorter capacitor discharge time is an indication of greater reflection. The LED current-limiting resistor is set to deliver approximately 17 mA to the LED when VIN is 5 V. The current requirement can be met by some microcontroller I/O lines, allowing the sensor to be powered up and down through an I/O line to conserve power. This sensor was designed to be used with the board perpendicular to the surface being sensed, and narrow-angle lenses built into the infrared LED and phototransistor packages allow it to be effective to a range of about 1?(25 mm). Because of its small size, multiple units can easily be arranged to fit various applications such as line sensing and proximity/edge detection. The QTR-L-1RC is sold in packs of two units. For a similar sensor that can be used with the board parallel to the surface, but with shorter range, please see the QTR-1RC reflectance sensor. QTR-L-1RC reflectance sensor on a quarter next to a QTR-1RC reflectance sensor. Specifications:

• Dimensions: 0.3? 0.35? 0.12? (without optional header pins installed)
• Operating voltage: 5.0 V
• Supply current: 17 mA
• Output format: digital I/O-compatible signal that can be read as a timed high pulse
• Optimal sensing distance: 0.125? to 0.25? (3 mm to 6 mm)
• Maximum recommended sensing distance: 1? (25 mm)
• Weight without header pins: 0.006 oz (0.2 g)

Interfacing the QTR-L-1RC Output to a Digital I/O Line: Like the Parallax QTI, the QTR-L-1RC module has sensor outputs that require a digital I/O line capable of first charging the output capacitor (by driving the line high) and then measuring the time for the capacitor to discharge through the phototransistor. This measurement approach has several advantages, especially when multiple units are used:

• No analog-to-digital converter (ADC) is required
• Improved sensitivity over voltage-divider analog output
• Parallel reading of multiple sensors is possible with most microcontrollers

The typical sequence for reading a sensor is:

• 1.Set the I/O line to an output and drive it high
• 2.Allow at least 10 us for the 10 nF capacitor to charge
• 3.Make the I/O line an input (high impedance)
• 4.Measure the time for the capacitor to discharge by waiting for the I/O line to go low

These steps can typically be executed in parallel on multiple I/O lines. With a strong reflectance, the discharge time can be as low as several dozen microseconds; with no reflectance, the discharge time can be up to a few milliseconds. The exact time of the discharge depends on your microcontroller?s I/O line characteristics. Meaningful results can be available within 1 ms in typical cases (i.e. when not trying to measure subtle differences in low-reflectance scenarios), allowing up to 1 kHz sampling. The following table shows some typical discharge times (from 5 V down to a 2 V threshold) of the sensor over different surfaces and at different distances:

Ambient light, especially sunlight, can affect the sensor readings significantly. If the discharge time of the QTR-L-1RC is consistently low, you might need to add shielding around the sensor or mount it in a different location to reduce interference from outside light sources. Pololu AVR library provides functions that make it easy to use these sensors with our Orangutan robot controllers; please see the QTR Reflectance Sensors section of Pololu’s library command reference for more information. We also have a Arduino library for these sensors. Included Components: Each pack of two reflectance sensors includes sets of straight male header strips and right-angle male header strips, which allow you to mount them in the orientation of your choice. You can also solder wires, such as ribbon cable, directly to the pads for the most compact installation. QTR-L-1A or QTR-L-1RC reflectance sensor (2-pack) QTR-L-1A and QTR-L-1RC reflectance sensors mounted with included header pins. in a breadboard.
Documents:

• Pololu QTR Reflectance Sensor Application Note
• Pololu AVR C/C++ Library User?s Guide
• Arduino Library for the Pololu QTR Reflectance Sensors
• Pololu AVR Library Command Reference
• Building Line Following and Line Maze Courses